Janty® eGo Tank system
The Janty® eGo Tank System builds on the achievements of the original Janty® eGo designed by Janty® in October 2009, and copied by many. Its huge 650mAh battery enables users to experience over 600 puffs a day. The Janty® eGo Tank System applies a tank system for dripping e-liquid directly into its 1.1ml tank cartridge without the use of fine tissue inside the tank.

The Janty® eGo Tank System set consists of a tank cartridge, tank atomizers and normal Janty® eGo batteries (with power cut off function).

Charging
The Janty® eGo uses a 3.7volt, 650mAH rechargeable battery. The safety function allows you to turn the battery off and on to prevent accidental discharge of the battery when not in use. It takes about 2 hours to charge battery. The Janty® eGo microchip prevents overcharging. The charger will automatically stop when battery is fully charged.

To charge the battery, gently screw the Janty® eGo battery into the USB charger, and plug the USB cable into a USB charger or a computer. The battery should flash a red light to indicate that it is charging. Once the green light flashes, the battery has been fully charged.


* You should use only the dedicated JANTY® eGo superfast USB charger provided to avoid damaging battery.

* Use the high voltage USB port to charge battery properly.

* Charge the battery fully before using to maintain a good battery life.


Assembling your Janty® eGo Tank System
To assemble the Janty® eGo Tank System, you need the battery compartment, an atomizer and a Janty® eGo Tank cartridge. First, screw battery compartment clockwise into the hole on the atomizer. Gently push the Janty® eGo Tank cartridge into the atomizer until you hear a click. Forcing the cartridge into the atomizer may cause damage.

Using the Janty eGo Tank System

The Janty® eGo Tank System only works when you press the LED button. Press the LED button and inhale at the same time and release the button right after inhaling. When you press the button, the LED light will turn on. Pressing the button too long may cause overheating and damage the Janty® eGo. Between puffs, let the eGo JETS® rest for at least 20 seconds in order for the liquid to reach the atomizer cavity. Puffing too many times in  a row without pause can result in a dry harsh vapor feeling.

* Battery
The battery is shipped in an “OFF” state. While in the “OFF” state, the Janty® eGo will not function even when the atomizer button is pressed. To turn the battery “ON”, press the atomizer button 5 times within 2 seconds. You will see LED button flash. To turn off battery, press atomizer button 5 times in 2 seconds.

Always charge the battery fully before using to maintain a good battery life. To ensure a good battery life, do not store the battery in a hot or humid environment. Do not drop the battery. Do not force the battery into the battery compartment when assembling parts. Keep the battery away from sharp objects.

* Liquid
To prevent excess liquids from building up in the mouth piece, clean the overflow prevention cap and the vapor pathway frequently to prevent blockage. Clean excess liquids from around the refill hole before using. If you get excess liquids on your lips, wipe area immediately or wash with water.

Do not drink liquids. Use only as instructed. Keep liquids in a safe place away from children or pets. Do not store in a hot place. Keep liquids away from direct sunlight. Do not store in a cold place to prevent freezing. Improper storage will cause e-liquid to spoiI or Iose flavor.

* Atomizer
If the atomizer overheats, wait until it returns to a normal temperature before using. If the heating element in the atomizer is dry, it will produce a burning taste. Please ensure there is enough liquid in the tank to prevent heating element from drying.

Refilling the Iiquid
In other versions of the Janty® eGo, a fine tissue is used to hold the liquid in the cartridge. The Janty® eGo Tank System uses a different system. Just open the cap, drip the Iiquid into the cartridge and close the cap.
Open the top of the tank cartridge as shown in the picture. Drip liquid into the cartridge until it is full. Close the cartridge and follow the directions for assembling the Janty® eGo Tank System. Stop vaping when you experience a burnt taste, disassemble and refill the tank, then re-assemble. Take a few draws from the mouthpiece without activating the button to force liquid to flow into the atomizer. Wait a few seconds and activate the button while you take a draw.

Maintenance of the Product

To maintain the Janty® eGo’s well functioning, only use it per manual instructions and have it cleaned regularly.